2016 Mitsubishi Eclipse Electric tailgate lift installation

By HansShoW | 12/29/2020 |

Precautions

●All pictures in this manual are for reference only. The pictures and practices may be different, but the installation method is the same.
● In order to facilitate your installation, please read the instruction manual of the product carefully before installation; please pay attention to protect the surface of your car during installation to avoid scratching.
● Please check regularly if all the accessories connected to the car are tight to ensure safety

Common problems
1. The bracket installs in the wrong direction and the door cannot be closed. 2. The bracket screw is not changed as required: the door cannot be closed and the electric strut is damaged.
3. The control box connector is not inserted in place.
4. The ball head and the circlip are not installed in place: the struct pole is fall off during use (check after installation)
5. The connector is not inserted in place, shedding: function failure
6. the electric lock not in the central results in the door cannot close, the door gap is large
7. The car did not use for a long time, after installed the kit, because of lower power in battery, the tailgate cannot move normally, the car needs to re-ignite.
8.The rear door installed with sound insulation cotton more than 5 kg may affect the tailgate pull.
9. After the first installation or power failure, you can raise the tailgate to the desired height. Press and hold the switch button on the tailgate for 3-5 seconds. After hearing the drip sound, release your hand. Gently press the tailgate switch once, the tailgate will automatically close, then you will hear a dripping sound. Now, you complete the tailgate height setting.

Installation steps

1 Remove the original car stay and bracket, install the dedicated left bracket (the ball head is
facing outward), and install the bracket with the original ball head and the special gasket.
2. Remove the original car stay and bracket, install the special right bracket (the ball head is
facing outward), and install the bracket with the original ball head and the special gasket
3. Remove the original car waterproof rubber plug, the strut bracket line passes through the
reserved hole of the original car to the tailgate control box, and put on rubber stopper.
4. Remove the decorative panel under the driver seat, find the power supply, unplug the
yellow 20A fuse of the original car, plug in our power plug instead.
5. Remove the trim panel under the A-pillar of the driver seat. Our yellow central control line
is connected to the blue-and-white line of the port (the second pin in the first row from left to
right)
6. removes the original car empty button under the driver seat and installs our special front
tailgate switch button.
7. Locate the port at the tailgate of the car, unplug the original terminal and plug it into our
front switch terminal.
8. Connect the power ground wire at the back door of the car
9. Unplug this port from the original door lock and insert it into our three-way adapter socket
10. Remove the original car lock buckle, install the special electric suction lock buckle, and
fix it with our screws.
11. Remove the original car lock, install our electric suction lock, and fix it with the original
car screws
12.Plug the socket as shown in the figure
13. plug strut bar, electric suction lock wire and power cord in the control box according to
the color
14. Make a hole on the left side of the tailgate trim to install the tailgate switch button

After the installation is complete, please do the tailgate learning settings, please make sure the door can be closed in the right position. Press and hold the switch button on the tailgate for 3-5 seconds. After hearing the drip sound, release your hand. Gently press the tailgate switch once, the tailgate will automatically close, then you will hear a dripping sound. Now, you complete the tailgate height setting.

Disclaimer :The related problems and losses caused by improper installation and use are not covered by our company’s warranty. Thank you for purchasing the hansshow intelligent electric lift door. Please read this manual carefully before use. Please keep it carefully after reading it for future reference. The picture is for reference only, the product is subject to the actual product.

Button control method :
1. Presses the unlock button three times in the original car remote control key can open or close the tailgate.
2. Presses the front switch button 1 time can open or close the tailgate.

Possible problems and solutions
1.The original car remote control did not work Make sure the yellow line and the central control line are well connected.
2.Does not work after installation Check if the positive power cable is connected to 12V-16V Check if the power cord and fuse are connected. Check if the ground wire is connected.
3.Tailgate move not in right position Are the left and right brackets of the poles reversed? Is the box wire plugged in? Is the bracket fixed to the special screw? There are two black plastics on the left and right sides of the original rear door. If it falls off, it needs to be tightened.
4.The tailgate moves to half and stops . Are the left and right brackets of the poles reversed? . Is the box wire plugged in? . Is the bracket fixed to the special screw?

Product link:https://www.hautopart.com/product/mitsubishu-eclipse-cross-2019-power-tailgate/

Posted in Car tailgate & power running board news

Leave a Comment