Audi/Porsche Electric closing door installation main point

Introduction
Thanks for choosing our electric closing door, our product should bring you a kind of comfort、safe、and convenient feeling .
This manual will introduce you the Audi series electric closing doors’ function、 installation、and performances. Before using this product, please read this manual carefully.
To guarantee the normal functioning of this product, please act accordingly as this manual describes, avoid improper operation which may lead to losses and human injury .
This intelligent electric closing door and its’ accessories belong to our company property , it is protect by Chinese law.

Product link:https://www.hautopart.com/product-category/Soft-Closing-Doors/

A, Driver side door sheet take out

1,use pry Panel Disassembly Tool to take out the decorative sheet
2,use pry panel disassembly tool to take out the small sheet near the handle
3,Take out three set screws
4,Use pry panel disassembly tool to take out the snap joint around the door.( notes: before you take out the inner decorative sheet, make sure the set screws all release)
5,Detach the cable connections, take out the sheet
6,Use pry panel disassembly tool to take out the acoustic panel
7,Unveil the rubber cover of driver side key to the lock body, detach the door lock set screws
8,Use pry panel disassembly tool to take out the cover, take out the lock body
9,Take out the original lock body from inner side of the door.
10,Keep the original lock body well

B,Mental lock body detached

11, Position the lock body on the fix workbench, take out the protective sheet
12, Take out the door drag-line, value torsional spring, detached the screws of cover
13,Use rod smaller than M5 or screw driver to turn the lock bolt to complete lock
position( attentions in this step: avoid the damages of door lock sensor while the lock core detach from the lock controller.
14, Detached three set screws form the original car lock
15, Use tweezers to separate the L type transmission arm and fixed it, prepare for next steps’
separation work
16, Use tweezers or small slotted screwdrivers to pushing the middle between yellow slide arm and the original car door controls units’ white rotate connecting rod, be carefully and evenly separate them.(attentions: pushing carefully avoid damage the other parts)
17, Use tweezers or small slotted screwdriver to pushing the middle between the yellow original car door controller and the green slide arm, carefully and evenly separate them.(attentions: separate them carefully, avoid damage the other parts)
18, Parallel pulling the original car lock controller out from the mental lock corner.
19, The separation of the mental lock core and the car lock controller

B, Audi/Porsche soft close door lock installation step

1, Use a rod to push the clock blot to complete locking positions
2, Used the tweezers to anti-clock wise (1)rotate the L type transmission arm and fix them.
The fix position should like (2)
3, Put the holder form accessories box into lock hole as picture show, the bottom face of the holder should attach the metal plate surface.
4, 1),put the yellow outdoor handle arm positioning column into holders’ hole .2), put the green indoor handle arm positioning column into holders’ hole.
5, Use a pliers to cut the blue part ,the cutting surface should be parallel with the green face.
6, Original car lock controller unit assemble with electric close door lock unit, A1 transmission arm to green indoor handle bar, A2 transmission arm to yellow outdoor handle bar.
7, Put on the anti-dust cover and put on two fasten screw
8, Put on a fasten screw , take out the holder, the installation is complete.

Audi/ Porsche soft close door lock installation(back doors with child safety lock)

1, Back left door with child safety lock should pull the lock core as above arrow show, the final position should look like (2).
2, Back right door with child safety lock should pull the lock core as above arrow shows, the final position should look like (4)

E, Motor box sticky fix installation step

1, Soft close door lock parts
2, Put the soft close door lock body to the original position, recover the key inside the lock core
3, Clean the surface being attach, make sure not dust、water、oil exist on the surface, open the swelling binder , used the binder paper to wipe the surface, wait a few minute to dry.
4,Tear the 3M glue sticky protective paper, push the motor on the installation position make sure it is stick tight.
5,Tear off the protective paper on the 3M glue sticker, stick the devices above or beneath the out door handle bar.
6, After stick installation use ribbon to fasten the motor box(tips: differ car model may have subtle difference , but the installation step is the same)

Electrical connections(car door with BCM box for stable power supple)

1,The yellow positive line connect to +12V, the black negative line connect to GND, use a pliers to connect the cables tightly , use a multimeter to check the 12V output. Attention: shake the cables while check the 12V output for improper connections
2,Connect the motor box cable to power supple cable, test whether the soft close door lock
working properly, whether the outer door handle open door normally, if every thing all right,
recover the acoustic panel, manage the cable in a smooth way and fasten with ribbon. Attention:the cabling should better left the power connector and fuse under Lifting glass windows controller for latter check.
3, After the installation of soft close door lock, use a screw driver to push the lock core in half lock position, test whether the door suction normally. Pull the out door handle to unlock, repeat few more times to check the self suction function, make sure the inner door handle unlock, center control, child safe lock all working properly. After above test all done and every thing function normally,recover the decorative sheet.

Attentions: the pictures in this manual just for reference only,the real product may have subtle differences due to differ car model , but the installation step is basically the same

F , Brief trouble-shooting

If there’s malfunction of the soft close door lock, you can deal with the malfunction to the beneath file accordingly

One, the soft close door lock won’t work.
1,check every connectors for proper connection, check motor box cables, re-plug-and-insert again if necessary. 2,take out the suction lock body from the panel, keep power supple, straighten the dragline. Use a rod tools, pushing the lock bolt to half-lock position, simulate the close doors action, check if the motor box trigger the lock bolt for self-suction close motion, if all work properly, immature installation should take into account, adjust the installation(according to the instruction manual)

Two, the self-suction stiffly
1, check whether the dragline between motor box and lock head are wrapping or bend excessively , generally the dragline in the lock head side and motor box side are most vulnerable to bend, require special attention 2, if the dragline had not above situation, try unload the motor box, straighten the dragline. Use a rod tools, pushing the lock bolt to half-lock position, simulate the close doors action, check if the motor box trigger the lock bolt for self-suction close motion, if all work properly, immature installation should take into account, adjust the installation(according to the instruction manual)

Three, the self suction door can’t open
1, Break the fuse in power supple line or break the power circle malfunction single door for 3-5 minute, then re-power them to normal work 2, Check inside and outside door handle bar dragline for improper installation to loss
3, Back door inner handle bar can’t open the door, mainly checking the child safe lock switch open
4, Intelligent soft close door lock mainly check the lock bolt and the original car lock cooperate tightly , the lock bolt may installed improperly

Four, the self suction door can’t close
1,check whether the lock bolt stuck , try using the handle bar to open the lock bolt.
2,Take out the lock body and motor box from the door,straighten the dragline, test the lock bolt for smooth unlock.

Leave a Comment