Electric lift gate installation instruction (VW Tuguan L)

Function Description:

Height setting

Electric Lift Door Installation
1. Cautions: a. It’s only for reference with all pictures in this manual , the pictures may be different from the actual product, but it is the same with the installation method ; b. In order to facilitate your installation, please read the product manual carefully before installation; please protect the surface of your car during installation to avoid scratch; c. Please regularly check whether it ’ s loose with all the accessories connected to the car to ensure safety use;
2.Accessories List
(refer to this table to check whether it ’ s complete for the box accessories )

Wire harness

Volkswagen Tiguan L Car Looks

2.installation steps

a.Remove the panel, the specific steps as follows:

First remove the tail gate cover (shown by the arrow)
Take out the spare tire and remove the rear cover (shown by the arrow)
Disassemble the right inner trim panel (shown in red circle)
Remove the trim panel of the tailgate (shown by the arrow)
Remove the right threading rubber tube(as shown in the picture)

b. Install the bracket, the specific steps as follows:

Remove the left and right struts of the original car (use a screwdriver to pry
with the strut circlips)
Remove the bracket (as shown in the picture)
Install bracket (“L” is the left one, “R” is the right one)
Install the bracket (with the wire facing down)
Wiring with the strut(put the wire into the tailgate with the original car hole,
the same way with the left and right)

C. Wire The specific steps as follows:

Thread the door lock signal wire (blue and brown wire), switch signal wire
(white wire), negative wire and tailgate button wire through the threading
rubber tube to the tailgate trim pane
Note: Put wax on both ends of the threading tube to make wire more
conveniently
Remove the terminal of the manual switch wire and install the terminal after
threading the rubber tube. The color sequence of the wire is from left to right,
red, green, purple, pink
Pass the positive side of the power wire, central control switch wire (green wire)
and decoding wire (red and white wire, and orange one) to the driver seat

e. Install the door lock: the specific steps follows;

Remove the original car buckle, install the lock with the original car screws, and
tighten them.Plug with the plug terminal: insert the lock control wire on the harness, pay
attention to the color
Install the cable control box: Stick it with 3M glue

e. Wiring. The specific steps as follows:

Connect the signal wire and status wire: Make matched connection for the
converted plug.Or connect wire directly: the blue wire of the harness is connected to the
purple-white wire, and the brown wire is connected to the brown-white wire
Connect switch signal wire of the original car: Make matched connection for
the converted plug.Or direct wiring: connect the white harness wire (with black case outside the white wire) to the purple-blue wire
Connect the negative wire to the screw as shown
Connect the positive wire:
Remove the decorative parts on the fuse box and find the fuse holder at the
position shown in the picture.
Insert the fuse, and then plug it into the wiring harness. Note that the fuse
cannot be inserted reversely
Connect the decoding wire:
Unlock signal wire ( yellow wire) connect to brown-blue line of the B-pillar part.

f. Install the central control switch, the specific steps as follows:

Make sure there is no problem before punching
Install Central control switch : Punch the switch according to owner’s preference
Central control switch wiring:
The black wire is negative, the green wire is connected to the green one of the
product, and the yellow wire is positive (It won’t affect the function if we don’t
connect with yellow wire)

g. Install the tail switch, the specific steps is as follows:

Use a tool to make a hole at the position circled in red in the picture, and install
the switch.
Place the control box on the right side of the tailgate and fix it with the 3M glue
provided

h. Recover with the inner trim panel

It is the automatic learning mode of the control box at the first
time with the door opening and closing after power on . Please
make sure that the door can be opened and closed well. At this
point,the process of the electric lift door is finished.

3. Disclaimer: It won’t be in the warranty range from our company if it’s caused by improper installation and use.

Leave a Comment