Hyundai SantaFe 2019 (Lower Suction) Electric Tailgate Install Manual

By HansShoW | 10/15/2020 |

Features

The intelligent electric tailgate is suitable for high-end luxury cars. It has the functions of one-click control, intelligent anti-pinch, intelligent height adjustment, etc. It can be controlled by the tailgate button on the car key. It is easy to control and practical

Purchase link:https://www.hautopart.com/product/hyundai-tucson-electric-tailgate-2016/

Configuration list:

Control box
Strut*2
Tailgate button
Tailgate button cable
Power cable
Tailgate lock control cable
Electric suction lock cable
Cable tie*20
Make hole indication module
3M tape*2
Longer 3M tape
Hole opener (16 mm)

Precautions

1. Electric tailgate installation precautions For safety and to ensure the normal use of the product, please install it by professional staff.
2. Make sure that there is enough power in the car battery to ensure that the electric tailgate kit works properly. If the battery is low, test the electric tailgate after starting the engine for a while.
3. Before the electric pole is installed, the direction and position are determined to avoid damage caused by the reassembly and the circlip is loose. The ball head must be installed in place to prevent the electric pole from falling.
4. When laying out the CANBUS wire, power cable, button cable, and control box cable, it is necessary to clearly distinguish the specific connection methods of these cables to prevent misconnection.
5. Do not plug or unplug the connected cables while the power is on to avoid damaging the main unit

Lay wiring diagram

Steps for removing car trim plate

1.Open the tailgate and remove the original tailgate trim plate as shown

Steps for mounting bracket

1.Remove the original left and right steam poles
2.Remove the original tailgate ball stud and add two gaskets to install our ball stud

Steps for installing the brace

1.Install our electric struts, with the outlet end facing the body position of the car
2.Pass the pole line to the tailgate position at the originally reserved hole as shown

Steps for installing the electric suction lock

1.Remove the original trunk cover and remove the trim plate of the latch
2.Remove the lock hook
3.Install the standard electric suction lock of our company
4.Fix the electric lock device inside the left trim panel of the trunk

Steps for installing ECU

1.Connect all wiring harnesses and secure the control box

Descriptions of steps for other connecting wiring procedures

1.Unplug the lock and control line of the original car and plug it into the three- way lock and switch plug of our company (picture: position above the lock of the original car)
2.Put the control and ground wire on the ground screw of the original rear door
3.Run the power line and electric suction draw-lock wire along the wiring harness of the original car to the direction of the body of the car
4.Run the power line along the roof hose towards the main driver position. (picture: power cord, central control lock, signal cord)
5.Disassemble the pillar B trim plate; find the plug as shown in the picture; connect the green signal line of our company’s central control to the green line of the original car
6.Find the safety catch under the position of the driver
7.Unplug the safety catch of the original car to our electrical appliances as shown in the picture
8.Plug it back into the pole of safety catch to get electricity

Descriptions of steps for installing key switch

1.It’s suggested to punch hoes and press the switch button before installation as shown in the picture ( the same in the picture)
2.Install the switch button of the tailgate by punching holes as showed in the picture

Tailgate activation learning
Raise the tailgate to the highest position, press down about 2cm manually, long press the newly installed tailgate switch, after hearing the drop, release your hand, then press the tailgate button, the tailgate is automatically closed. The setup is complete.
If the door is not closed, you can manually push it gently to close the door.
Height setting
Raise the tailgate to your ideal height, press and hold the newly installed button for about 3 seconds, hear a drop sound, release your hand, press the tailgate button again, and the tailgate closes. The height setting is complete.
Key/button usage
The original car remote control key, long press the tailgate button to open the tailgate.
Click the tailgate button to open or close the tailgate
Disclaimer: The problems and losses caused by improper installation and improper use are not covered by our company’s warranty.

Posted in Car tailgate & power running board news

Leave a Comment