Skip to content

Hyundai Santa Fe 2019 (LowerSuction)ElectricTailgate Install Manual

Electric tailgate functions

1.Open and Close the power tailgate lift using kick sensor.
2.Open and Close the electric tailgate using the key fob.
3.Close the power liftgate kit with the supplied button (added in the automatic lift gate).
4.Open the universal power liftgate kit using front button.

product link:https://www.hautopart.com/product/hyundai-ix45-santa-fe-2016-2017-power-tailgate/

Configuration list

Hyundai Santa Fe 2019 (LowerSuction)ElectricTailgate Install Manual
Control box
Hyundai Santa Fe 2019 (LowerSuction)ElectricTailgate Install Manual
Strut*2
Hyundai Santa Fe 2019 (LowerSuction)ElectricTailgate Install Manual
Tailgate button
Hyundai Santa Fe 2019 (LowerSuction)ElectricTailgate Install Manual
Tailgate button cable
Hyundai Santa Fe 2019 (LowerSuction)ElectricTailgate Install Manual
Power cable
Hyundai Santa Fe 2019 (LowerSuction)ElectricTailgate Install Manual
Tailgate lock control cable
Hyundai Santa Fe 2019 (LowerSuction)ElectricTailgate Install Manual
Electric suction lock cable
Hyundai Santa Fe 2019 (LowerSuction)ElectricTailgate Install Manual
Cable tie*20
Hyundai Santa Fe 2019 (LowerSuction)ElectricTailgate Install Manual
Make hole indication module
Hyundai Santa Fe 2019 (LowerSuction)ElectricTailgate Install Manual
3M tape*2
Hyundai Santa Fe 2019 (LowerSuction)ElectricTailgate Install Manual
Longer 3M tape
Hyundai Santa Fe 2019 (LowerSuction)ElectricTailgate Install Manual
Hole opener (16 mm)
Hyundai Santa Fe 2019 (LowerSuction)ElectricTailgate Install Manual

Precautions
Electric tailgate installation precautions
For safety and to ensure the normal use of the product, please install it by professional staff.
 
Make sure that there is enough power in the car battery to ensure that the electric tailgate kit works properly. If the battery is low, test the electric tailgate after starting the engine for a while.
 
Before the electric pole is installed, the direction and position are determined to avoid damage caused by the reassembly and the circlip is loose. The ball head must be installed in place to prevent the electric pole from falling.
 
When laying out the CANBUS wire, power cable, button cable, and control box cable, it is necessary to clearly distinguish the specific connection methods of these cables to prevent misconnection.
 
Do not plug or unplug the connected cables while the power is on to avoid damaging the main unit.

Lay wiring diagram

Hyundai Santa Fe 2019 (LowerSuction)ElectricTailgate Install Manual

Steps for removing car trim plate

Hyundai Santa Fe 2019 (LowerSuction)ElectricTailgate Install Manual
1.Open the tailgate and remove the original tailgate trim plate as shown
Hyundai Santa Fe 2019 (LowerSuction)ElectricTailgate Install Manual
1.Remove the original left and right steam poles
Hyundai Santa Fe 2019 (LowerSuction)ElectricTailgate Install Manual
2.Remove the original tailgate ball stud and add two gaskets to install our ball stud

Steps for installing the brace

Hyundai Santa Fe 2019 (LowerSuction)ElectricTailgate Install Manual
1.Install our electric struts, with the outlet end facing the body position of the car
Hyundai Santa Fe 2019 (LowerSuction)ElectricTailgate Install Manual
2.Pass the pole line to the tailgate position at the originally reserved hole as shown

Steps for installing the electric suction lock

Hyundai Santa Fe 2019 (LowerSuction)ElectricTailgate Install Manual
1.Remove the original trunk cover and remove the trim plate of the latch
Hyundai Santa Fe 2019 (LowerSuction)ElectricTailgate Install Manual
2.Remove the lock hook
Hyundai Santa Fe 2019 (LowerSuction)ElectricTailgate Install Manual
3.Install the standard electric suction lock of our company
Hyundai Santa Fe 2019 (LowerSuction)ElectricTailgate Install Manual
4.Fix the electric lock device inside the left trim panel of the trunk

Steps for installing ECU

Hyundai Santa Fe 2019 (LowerSuction)ElectricTailgate Install Manual
1.Connect all wiring harnesses and secure the control box

Descriptions of steps for other connecting wiring procedures

Hyundai Santa Fe 2019 (LowerSuction)ElectricTailgate Install Manual
1.Unplug the lock and control line of the original car and plug it into the three-way lock and switch plug of our company (picture: position above the lock of the original car)
Hyundai Santa Fe 2019 (LowerSuction)ElectricTailgate Install Manual
2.Put the control and ground wire on the ground screw of the original rear door
Hyundai Santa Fe 2019 (LowerSuction)ElectricTailgate Install Manual
3.Run the power line and electric suction draw-lock wire along the wiring harness of the original car to the direction of the body of the car
Hyundai Santa Fe 2019 (LowerSuction)ElectricTailgate Install Manual
4.Run the power line along the roof hose towards the main driver position. (picture: power cord, central control lock, signal cord)
Hyundai Santa Fe 2019 (LowerSuction)ElectricTailgate Install Manual
5.Disassemble the pillar B trim plate; find the plug as shown in the picture; connect the green signal line of our company’s central control to the green line of the original car
Hyundai Santa Fe 2019 (LowerSuction)ElectricTailgate Install Manual
6.Find the safety catch under the position of the driver
Hyundai Santa Fe 2019 (LowerSuction)ElectricTailgate Install Manual
7.Unplug the safety catch of the original car to
our electrical appliances as shown in the picture

Descriptions of steps for installing key switch

Hyundai Santa Fe 2019 (LowerSuction)ElectricTailgate Install Manual

1.It’s suggested to punch hoes and press the switch button before installation as shown in the picture ( the same in the picture)

Hyundai Santa Fe 2019 (LowerSuction)ElectricTailgate Install Manual

2.Install the switch button of the tailgate by punching holes as showed in the picture

Tailgate activation learning
Raise the tailgate to the highest position, press down about 2cm manually, long press the newly installed tailgate switch, after hearing the drop, release your hand, then press the tailgate button, the tailgate is automatically closed. The setup is complete.
If the door is not closed, you can manually push it gently to close the door.

Height setting

Raise the tailgate to your ideal height, press and hold the newly installed button for about 3 seconds, hear a drop sound, release your hand, press the tailgate button again, and the tailgate closes.
The height setting is complete.

Key/button usage
The original car remote control key, long-press the tailgate button to open the tailgate.
Click the tailgate button to open or close the tailgate

Leave a Comment





Scroll To Top
WhatsApp Click here to whatsapp us