Skip to content

Tesla Model Y Power Frunk Installation Manual

Tools you need

Tesla Model Y Power Frunk Installation Manual

Product list

Tesla Model Y Power Frunk Installation Manual

Installation step

Tesla Model Y Power Frunk Installation Manual
1.Remove frunk trim panel
Open the hood and remove the trim from the sign.
Tesla Model Y Power Frunk Installation Manual
2.remove frunk trim panel
Remove the switch trim panel in the front spare
case and unplug the switch plug
Tesla Model Y Power Frunk Installation Manual
3.remove frunk trim panel
Remove the screws from the sign and remove
the entire trim panel.
Tesla Model Y Power Frunk Installation Manual
4.Install the strut
Use the panel pry bar to warp the steel plate
on the back of the tee head and remove the strut(see the diagram on the right)
Tesla Model Y Power Frunk Installation Manual
5.Install power struts
Use a screwdriver rermoves the original bracket, chang
to our negw bracket ,use the new scxew to fix it. (Based
on the model Y heading direction, L mean left bracket
R mean right bracket. Be careful when installing the
bracket, or you may break the bracket
Tesla Model Y Power Frunk Installation Manual
6.Install power struts
Correct and incorrect bracket installation
comparison chart Left is the correct one,
right is the incorrect image.
Tesla Model Y Power Frunk Installation Manual
7.Install power struts
install our powerruts, push the power strut hole into
the bracket ball head, putthe strut with wire end in the
bottom. After you install the power strut ,move the strut
left and right to confirm strus been installed well. (the
figure is about the right side installed power stmt).
Tesla Model Y Power Frunk Installation Manual
8.Install suction lock
Mark the edge of the original lock, remove the
two screws from the original lock and take out
the whole lock machine.
Tesla Model Y Power Frunk Installation Manual
9.Install suction lock
Install the pull-rope of the electric suction
actuator on our bracket.
Tesla Model Y Power Frunk Installation Manual
10.Install suction lock
Remove the torsion spring at the mark and hang our bumper on the column at the indicating post.
Tesla Model Y Power Frunk Installation Manual
11.Install suction lock
Recover the indicated spring.
Tesla Model Y Power Frunk Installation Manual
12.Install suction lock
Put the lock back on the car.
Tesla Model Y Power Frunk Installation Manual
13.Install suction lock
Fix the actuator and draw the emergency
rope of the actuator to the emergency joint.
Tesla Model Y Power Frunk Installation Manual
14.wiring picture two
Tesla Model Y Power Frunk Installation Manual
15.wiring picture one
Tesla Model Y Power Frunk Installation Manual

setting

height adjustment
adjust the tailgate to the appropriate height,press and hold the tailgate button for 5 seconds, and hear a long beep that indicates the height setting is successful.

speed adjustment
the tailgate swtich speed is divided into 5 gears,the default is 4 gears,the lowest 2 gears,and the highest 6 gears. press and hold the tailgate button.when the buzzer sounds 2 consecutive sound,it means that the speed setting 2 is successful.when the buzzer is heard for 3 consecutive sound,the speed setting 3 is successful,and so on.

Tesla Model Y Power Frunk Installation Manual

Note:After the installation is completed. the controller needs to be matched when the power is plugged in: the electric tailgate is adjusted to the highest
position. and the tail button is pressed for 5 seconds. After a long beep, the button is released. indicating that the matching operation is completed. (If
the power off requires a rematch operation).

Tesla Model Y Power Frunk Installation Manual

Note:The installation instructions may differ slightly from the actual operation. If there are any differences. please follow the actual situation or
contact us.

Tailgate strength adjustment:
Adjustment When the door cannot be opened or the door cannot be closed:Adjust position: The small black button of the control box (decoder).

Tuning method:
First, the door can not be opened (the door opening is not good)
Press and hold the small black point switch on the control box to adjust the strength of the opening tailgate . Clicking the black dot 3 seconds, Then, Press and hold the switch, the buzzer will beep 1 to 5 times, 1 sound is the smallest strength, 5 sound is the strongest,and the factory default is 1sound;
Second, the door can not be closed (the door closing strength is not good) :
First, use a screwdriver turn the tailgate lock to close status. (equivalent to closing the door, you must make the tailgate lock in lock status when adjusting the closing force), and then press and hold the small black point switch on the control box to adjust the closing strength. The strength, long press the switch buzzer will ring from 1 to 5 times, 1 sound is the smallest, 5 sound is the strongest, the factory default I sound, generally adjusted to 3 sounds, test the closing strength, if still feel not good, try other strength;
Tailgate speed adjustment:
The speed is divided into 5 levels, and the default is 4 level. The lowest 2 level, the highest 6 level,Press and hold the tailgate button over 5 seconds. When you hear 2 beeps, the speed of the 2nd level is set successfully-Press and hold the tailgate button. When you hear 3 beeps, the speed of the 3rd level is set successfully. Press and hold the tailgate button. When you hear 4 beeps, the speed of the 4th level is set successfully. And so on.

Tesla Common Problem Causes & Solutions Analysis

1.Front cover not level from left to right
Adjust the upper bracket screw on the uneven side, loosen the screw slightly then control the frunk to close, the bracket will automatically fine-tune to perfectly close the front cover, then tighten the screw.
If the method does not work:
Check whether the lock is placed horizontally. If not, loosen the two screws on the lock, make the lock horizontal,then tighten the screws.

2.Mobile App can not open the frunk
Cause:
1.The motor plug is not tightly inserted, or it is forgotten to be inserted. Solution: Insert the motor plug tightly.
2.Frunk lock problem:
If the frunk can not be open, check the locks to decide whether it is a problem caused by gear one or gear two locks
1 ) The problem is on gear 2 locks if the frunk opens a little when pushing the frunk button.
First, try using the mobile app frunk button several times to see if the frunk can be opened. lf yes, click (not long press) the small black dot on the control box and hear two beeps.lf not, pry the lock.(Working Theory: When
closing the frunk, the motor steel wire will draw closer to the ball stud. After closing, it will make a ” z-” sound.Loosen the wire, if there is no ” z-” sound, it means the lock is jammed. At this point, you need to pull the
emergency lock wire, so the steel wire connected to the balL stud will be loosened, then the lock can be opened normally)
2) The problem is on one lock if the frunk completely does not react when pushing the button.Check whether the original car motor plug is plugged in. If yes and the frunk still cannot work, the problem is on the original car motor. Contact Tesla Customer Service.

There are warning sounds of front cover being opened during driving; Press the horn or brake pedal, the screen sends warning of irregularity
Cause 1 : After connecting the Y commissioning plug to adjust the front cover opening and closing speed, the original button plug is not restored.
Solution: Restore the original frunk button plug.
Cause 2: The signal status cable has poor contact or is loose. It leads to the screen showing the frunk is open, even when the frunk is closed.
Solution: Insert the status cable plug tightly.

The front cover can only be closed but cannot be opened

Cause: When opening the frunk, the gear 2 lock hooked on to the lock ring.
Solution:
1 )Adjust the opening force and opening speed;
2)Adjust the unlock mode through the small black dot on the control box. Click once the small black dot to make
the control box beep twice;
3) Contact us to update the software.

The front cover cannot be locked or can not move
Cause: The position of the lock is improper, Frunk strut resistance too heavy.
Solution: Adjust the position of the lock; Moving the Frunk cover up and down for 10 times.

Control Box Light Status Indication

1.Normal state:
Solid green, blinking red.
2.Both lights are solid:
System is in upgrade mode. Ifthe two lights keeps solid all the time, power off then power on to solve the problem.
3.The lights are dim, fast blinking, or slowly blinking:
Check whether the ground wire is connected properly. The ground wire must be connected to unpainted metal.
4.Both lights are off:
The system is dormant. There are two solutions.
1.First try to activate the control box with the app, button, key, etc. If not work, try solution
2;Use a screwdriver to short the control box power plug, so as to discharge the control box system.
5.Control box keeps sounding:
It may be that the button is pressed and does not rebound, or that the lock panel is too high, the button should be reinstalled at another proper position; or just push the lock panel down.

Precautions of Frunk and Trunk Installation
1.Trunk strut Installation
1 ) Take care to use a towel to prevent the glass from being scratched or ruptured when removing the struts.
2) When installing the strut to the original car, pay attention to the copper sheet, make sure it is not protruding.
2.Lock Installation
1 ) Mark the position of the original lock with a pen, and fix the new lock to this position.
2) If there is a gap when the tailgate is closed, the lock should be adjusted downwards.
3.Strut Cable Installation
When passing the cable into the trunk, keep a certain sagging arc to prevent water ingress.
Disclaimer: The problems and losses caused by improper installation and
improper use are not covered by our company’ s warranty.

product link:https://www.hautopart.com/product/model-y-power-frunk-trunk-kick-sensor/

Leave a Comment





Scroll To Top
WhatsApp Click here to whatsapp us