Toyota Saina Smart electric lift gate installation instruction

By HansShoW | 12/22/2020 |

Function Description:

Height setting：

Open the tailgate manually to the height you want, press and hold (about 2
seconds) the tailgate switch(as shown in the picture below), and immediately
release your hand after hearing the buzzer sound. After the height is set, press
the manual switch button to close the tailgate automatically. Open the tailgate
again to be the height you set.

Electric Lift Door Installation

1. Cautions:
a. It’s only for reference with all pictures in this manual , the pictures may be different from the actual product, but it is the same with the installation method ;
b. In order to facilitate your installation, please read the product manual carefully before installation; please protect the surface of your car during installation to avoid scratch;
c. Please regularly check whether it’s loose with all the accessories connected to the car to ensure safety use;
d.Warm Mention

2. Accessories List
(refer to this table to check whether it’s complete for the box accessories )

Install step

Toyota Saina Car Looks
a.Remove the panel, the specific steps as follows:
Refer to the accessories list and its picture to check if the parts are complete
Remove the inner panel of the tailgate (shown by the arrow)
Remove rubber tube of the threading on the left (as shown in the picture)
b. Install the bracket, the specific steps as follows:
Remove the left and right struts of the original car (pry it by Strut circlip of
flat-blade screwdriver )
Remove the bracket (as shown in the picture)
Install bracket (“L” is the left bracket, “R” is the right bracket)
Install the strut(with the wire end up)
Wire struts (put the wire into the car tailgate hole, the same way for the left and right)
C. Pass through wire. The specific steps as follows:
Wire the positive wire of the power supply, the central control switch wire
(green wire) and the decoding wire (red, white and orange wires) into the car
body through the threading rubber sleeve.
Put these wires into car inside by the rubber coat for Power
wires(“+”side,“-”side), Central control switch wire(Green one)and Decoding
wire(The red and black one ,and orange one)
Note: Put wax on both ends of the rubber tube to pass through wires
Pass through these wires into driver space for Power wires(“+”side,“-”side),
Central control switch wire(Green one)and Decoding wire(The red and black
one ,and orange one)
Pass through these wires into driver space for Power wires(“+”side,“-”side),
Central control switch wire(Green one)and Decoding wire(The red and black
one ,and orange one).
d. Install the door lock: the specific steps as follows:
Remove the three screws of the original car lock (shown in red circle)
Install the electric suction lock equipped
Tighten the screws removed from the original car
e. Wiring. The specific steps as follows:
Plugged in Red circle , wiring harness connection with green circle
Or connect directly: the blue wire of the wire harness is connected to the blue
wire, and the brown wire of the wire harness is connected to the gray wire
Connect switch signal wire of the original car : the converted plug inserted;
Or direct wiring: connect the white wire harness (with black wrap outside the
white wire) to the blue wire
Connect the negative wire:
Connect the negative wire to the screw as shown
Connect the positive wire:
Remove the decorative parts on the fuse box and find the fuse holder at the
position shown in the picture
Connect the negative wire:
Connect the negative wire to the screw as shown
Connect the positive wire:
Remove the decorative parts on the fuse box and find the fuse holder at the
position shown in the picture
Insert the fuse, and then plug it into the wiring harness. Note that the fuse
cannot be inserted reversely
Connect the decoding wire:
Make matched connection for decoding wire and OBD wire
f. Install the central control switch, the specific steps as follows:
Central control switch installation:
Disassemble the decorative cover at the position (the red circle in the
picture)and then buckle the central control switch directly in.
Central control switch wiring:
As shown in the picture, it is connected to the positive side of the small light of
the next button by the yellow wire (if it doesn’t need the small light, it couldn’t
connect with yellow wire, which will not affect the switch function)
g. Install the tailgate switch, the specific steps as follows：
Remove the decorative part at the position circled in red in the picture, and
install the switch.
h. Place the main box:
Place the control box on the tailgate and fix it with the 3M glue provided
It is the automatic learning mode of the control box at the first time with the
door opening and closing after power on . Please make sure that the door can
be opened and closed well. At this point,the process of the electric lift door is
finished.

Disclaimer:
It won’t be in the warranty range from our company if it’s caused by
improper installation and use.

Thank you for purchasing the smart electric lift gate. Please read this
manual carefully before using it, and store it carefully after reading
it.For future reference,the pictures are for reference only, and please follow with the actual products.

Posted in Car tailgate & power running board news

Leave a Comment