Skip to content

Toyota Soft Close Door Installation Instruction

a. Remove the driver side door. Same procedure for the passenger side:

Toyota Soft Close Door Installation Instruction
1.Use a pry bar to carefully pry
open the inner door handle trim
plate ( Picture 1 b), pry open the
horn panel ( Picture 1 a), pry
open the inner door armrest trim
plate (Picture 1 c )
Toyota Soft Close Door Installation Instruction
2. Use a pry bar carefully
pry open the glass elevator
trim.
Toyota Soft Close Door Installation Instruction
3.Remove two connection
signalers on the back of the
decorative plate.
Toyota Soft Close Door Installation Instruction
4.Remove the fixed screws
in the red circle.
Toyota Soft Close Door Installation Instruction
5.Remove two fixed screws
in the red circle.
Toyota Soft Close Door Installation Instruction
6.Use a pry bar carefully pry off the
surrounding clips along the edge of the door
trim panel, then remove the door trim panel.
Toyota Soft Close Door Installation Instruction
7.Remove the two ties on the
back of the door trim panel.
(showed in the red circle)
Toyota Soft Close Door Installation Instruction
8.Remove the connected plug.
(showed in the red circle)
Toyota Soft Close Door Installation Instruction
9.Use a knife carefully slice the
soft rubber along the edges of
the sound-proofing sponge.
Toyota Soft Close Door Installation Instruction
10.Use a 10MM screwdriver
socket remove the screw in
the red circle.
Toyota Soft Close Door Installation Instruction
11.Use a T30 screwdriver
to remove three fixed
screws from the door lock.
Toyota Soft Close Door Installation Instruction
12.Take the original car
door lock out from the door.

b.Remove the rear right door (Same procedure for the rear left door)

Toyota Soft Close Door Installation Instruction
1.Use a pry bar to carefully pry
open the inner door handle trim
plate.
Toyota Soft Close Door Installation Instruction
2. Use a pry bar carefully
pry open the glass elevator
trim.
Toyota Soft Close Door Installation Instruction
3.Use a pry bar to carefully pry
open the inner door handle trim
plate.
Toyota Soft Close Door Installation Instruction
4.Remove the connection
signalers on the back of the
decorative plate.
Toyota Soft Close Door Installation Instruction
5.Use a phillips screwdriver to
remove the fixed screws in the
red circle
Toyota Soft Close Door Installation Instruction
6.Remove right center
column glass trim
Toyota Soft Close Door Installation Instruction
7.Use a pry bar carefully pry
off the surrounding clips
along the edge of the door
trim panel, then remove the
door trim panel.
Toyota Soft Close Door Installation Instruction
8.Remove the two ties on the
back of the door trim panel.
(showed in the red circle)
Toyota Soft Close Door Installation Instruction
9.Remove the connected plug.
(showed in the red circle)
Toyota Soft Close Door Installation Instruction
10.Use a knife carefully slice the
soft rubber along the edges of
the sound-proofing sponge.
Toyota Soft Close Door Installation Instruction
11.Use a 10MM screwdriver
socket remove the screw in
the red circle.
Toyota Soft Close Door Installation Instruction
12.Use a T30 screwdriver
to remove three fixed
screws from the door lock.
Toyota Soft Close Door Installation Instruction
13.Installing the electric door
latch on the original door
lock.
Toyota Soft Close Door Installation Instruction
14.Secure the electric
door latch with the two
fixed screws of the original
latch. (showed in the red
circle)
Toyota Soft Close Door Installation Instruction
15.Use the electric suction door lock
cylinder card hole to mate with the original
internal linkage. Note: This step is to install
the front door lock
Toyota Soft Close Door Installation Instruction
16.Aligning the outer door handle with the unlocking arm
to the unlocking mechanism on the locking head and
securing the locking head.
Note: This step is for the rear door lock installation.
Toyota Soft Close Door Installation Instruction
17.Secure the door locks with
the 3 original door lock fixing
screws, then pull the locking
cylinder to the locked position
with a screwdriver.
Toyota Soft Close Door Installation Instruction
18.Pull the door handle to see if
the lock cylinder springs back to
the open position. If it springs
back normally, continue to install
the following steps, if not, check
the previous installation and
reinstall.
Toyota Soft Close Door Installation Instruction
19.Remove the sponge from
the accessory, peel off the
back of the sponge and
wrap the motor case with
the sponge
Toyota Soft Close Door Installation Instruction
20.Remove the two straps
and thread them through the
holes of the motor case
components.
Toyota Soft Close Door Installation Instruction
21.Smooth out the zipper
and turn the motor case.
Forward or reverse rotation.
Keeps the lock fully locked
into the cylinder.
Toyota Soft Close Door Installation Instruction
22. Use the ties to fasten
the motor case to the
position in the red circle.
Cut the excess ties off.
Toyota Soft Close Door Installation Instruction
23. Use the ties to fasten the
motor case to the position in
the red circle. Cut the excess
ties off. This step is to install
the rear door motor case.
Toyota Soft Close Door Installation Instruction
24.Secure the cable between
the lock cylinder and the
motor case with a tie in the
red circle position.

d. The wiring diagram of soft close door :

Toyota Soft Close Door Installation Instruction
1.Use pry bar to pry open the
left and right front door
welcome pedals
Toyota Soft Close Door Installation Instruction
2.Use pry bar to pry open
the left and right B-pillar
decorated trim.
Toyota Soft Close Door Installation Instruction
Toyota Soft Close Door Installation Instruction
Toyota Soft Close Door Installation Instruction

Leave a Comment





Scroll To Top
WhatsApp Click here to whatsapp us