Skip to content

Como instalar um elevador elétrico de porta traseira para Nissan Qashqai 2011 ~ 2019

Purchase address:

https://www.hautopart.com/product/electric-tailgate-lift/

Features

The intelligent electric tailgate is suitable for high-end luxury cars. It has the functions of hand-in-one opening, intelligent anti-pinch, intelligent height adjustment, etc. The driver can control tailgate with the car key tailgate button. It is easy to control and practical.

 

 

Electric tailgate functions

Easy to open

The electric tailgate can be controlled by the tailgate switch and the vehicle key.

Intelligent anti-pinch

When the electric tailgate is opened or closed, obstacles are encountered, and the tailgate can stop running to protect the user.

 

Disclaimer: The problems and losses caused by improper installation and improper use are not covered by our company's warranty.tailgate lift

automatic liftgate

Original car appearancepower liftgate

  1. Open the qashqai 2018 tailgate

electric lift gate

3: Remove the screw in the circlepower lift tailgate 

4: Pry the tailgate decorative panel and remove it

power liftgate kit

5: After pry the tailgate decorative, the effect of the tailgate decorative panel is as follows:

truck tailgate lift cars vehicles

6: Pry Anti-collision rubber column

power liftgate

7: Pull out Anti-collision rubber column and tear down Anti-collision rubber column Base

power liftgate

8: After pull out Anti-collision rubber column, this hole is Body bracket fixing screw hole

power liftgate

9: pry Spring circlip, then pull out the spring circlip.

power liftgate

10:Pull out Body ball stud.

power liftgate

11: Fix the body bracket on the car body(Install the bottom of the body bracket against the body guide)

power liftgate

12: Hold the screw of the tailgate bracket fixing nut piece of our company with your finger, and insert the nut piece into the square hole above the tailgate.

power liftgate

13: For the screw hole position, put your hand into the tailgate metal sandwich to fix the nut piece and tighten the screw.

power liftgate

14: Tighten the other screw and secure the bracket.

power liftgate

15: Install our electric poles.

power liftgate

16: Position the pole power cord, punch the hole in the red circle as shown below, and pass through the power cord (the drill bit is 16mm).

power liftgate

17: Remove the tailgate lock decorative panel.

power liftgate

18: Install the pull-tab and limit bracket.

power liftgate

19: After replacing the zipper bolt, the original car limit glue is mounted on the limit bracket.

power liftgate

20: Open the button on the left side of the trunk. In order to facilitate the installation of the zipper motor.

power liftgate

21: Pull the decorative panel on the left side of the trunk. The drive box is placed in the direction of the arrow as follows.

power liftgate

 

22: Pull out the decorative panel of the driver's seat. Can see the original car 0BD plug

power liftgate

23: The effect picture after pulling open is as followspower lift tailgate

24: Docking with the original car OBD, the effect is as follows

power lift tailgate

25: Use the crowbar to open the left side cover of the driver's seat

power lift tailgate

26Find 30A common power supply in the original car fuse box

power lift tailgate

27At the upper left of the driver's seat, punch the front center button.

power lift tailgate

28Route the power cord along the bottom of the left door trim panel.

power lift tailgate

29Red power cord, yellow for the zip line and orange for the ground.

power lift tailgate

30Pass the power cord and zip line through the left bellows.

power lift tailgate

31Route the power cord and zip line along the left side to the tail door lock.

power lift tailgate

32Attach all harness connectors and secure the control box to the red circle. As shown below.

power lift tailgate

33Pull out the original tailgate lock harness connector and dock with our harness connector.

power lift tailgate

34Pull out the original tailgate handle and find the button harness connector to connect with our harness connector.

power lift tailgate

35 The ground wire is in the left corner of the tail box as shown.

power lift tailgate

36Fix the negative ground wire of the power supply to the screw on the left side of the tail box. This screw is in the left corner of the decorative panel of the lock bolt. (Please connect the ground according to the recommended position of our company, otherwise the button on the front of the key will not be normal.)

power lift tailgate

37Install the tailgate button on the tailgate trim panel. As shown in the figure, restore the trim panel. After the installation is complete, manually close the tailgate reset once for system initialization.

 

Deixe um comentário





Scroll To Top
WhatsApp Click here to whatsapp us